Item Code | Image | Description |
---|---|---|
Item Code 4245247 |
Far End Device (FED 2) The FED 2 device will enable technicians delivering service over copper wires to perform PQT prior to installation. FED 2 can terminate the copper pair in a number of different configurations including: trace tone, insertion loss up to 24 MHz, Dis’, loop & through mode. Kit contents: FED2, Zipper Pouch, Lanyard, PSU. |
|
Item Code 026578 |
Test Telephone 300C Analogue test telephone with loudspeaker capability. Alerts to the presence of unsafe voltages and digital services on the line under test. Water-resistant construction, floats. Earth Recall option Learn More |
|
Item Code 315569 |
Oscillator 87J Tone generator most commonly used with hand held probe 500XP or earlier Amplifier 109J to identify cable pairs. Also used with Amplifier 109K and accessories to perform cable location. It generates a precision 1kHz tone at any of 4 cadence rates. LED lights to indicate a short circuit. Includes a Capacitor to provide DC isolation. Water-resistant and floats. Learn More |
|
Item Code 093653 |
Amplifier 500XP New amplifier probe used in conjunction with Oscillator 87J & exchange-based CPI tone. New digital filtering technology eliminates electrical noise. acAlert™ feature warns of hazardous voltages. Mode adjustability of gain and signal strength LEDs. Replaceable metal or carbon loaded plastic tip. Robust & water-resistant ergonomic design Learn More |
|
Item Code 096332 |
500XP Amplifier Headset Replacement Headset for the 500XP Amplifier only. Note: not compatible with previous amplifier versions. |
|
Item Code 315584 |
Amplifier 109K A water-resistant and tougher replacement for the old Amplifier 109G preferred by faultsman joiners for cable tracing and pair proving. Allows the use of: .
|
|
Item Code 315588 |
Tester 132K Kit designed for cable tracing, cable verification and pair proving. The kit includes:
|
|
Item Code 379680 |
NG Harrier 2 – ISDN2 Handheld Tester Verify Basic Rate ISDN circuit operation with the standalone handheld unit or connect to the PC to fully test the installation. PC software provides hypertext help information that can easily be updated to reflect current work practices to support testing and fault finding. Learn More |
|
Item Code 023858 |
Load Attenuator 20db Provides attenuation of ADSL signals to simulate long telephone lines. Used to determine if impairments other than attenuation are affecting the ADSL service. Learn More |
|
Item Code 023857 |
Load Attenuator 40db Provides attenuation of ADSL signals to simulate long telephone lines. Used to determine if impairments other than attenuation are affecting the ADSL service. Learn More |
|
Item Code 027123 |
Meter Multifunction 1B True RMS, auto-ranging, digital hand held meter with a 3-5/6 digit, 5000 count, liquid crystal backlit display with Bar Graph. Meter comes complete with carry case and GS38 rated test leads, including croc clips and probes, fused at 10A |
|
Item Code 003043 |
Adapter Test 4A Modular Adaptor to access wires terminated on Krone strip. No Break connection. Learn More |
|
Item Code 003965 |
Adapter Test 3B Modular adaptor with standard BT plug 431A, to access wires in NTE. Learn More |
|
Item Code 109055 |
182cm Viavi DSL Test Lead 182cm, Viavi DSL Test lead: RJ45-2 x 4mm shrouded banana. Perform Service Testing of DSL circuits using Viavi Handheld Tester. Learn More |
|
Item Code 109054 |
182cm Exfo DSL Test Lead 182cm (6’), Exfo DSL Test lead: RJ11-2 x 4mm shrouded banana. Perform Service Testing of DSL circuits using Exfo Handheld Tester. Learn More |
|
Item Code 084418 |
HHT Copper Lead Red/Black 175 cm test lead with controlled twist for accurate test results. 2 mm shrouded plugs at one end terminating in 4mm, non-retractable shrouded plugs at the other end. Can connect straight in to AdaptaJack block. |
|
Item Code 084419 |
HHT Copper Lead Green Green coloured 171 cm test lead. 2 mm shrouded plug at one end terminating in 4mm, non-retractable shrouded plug at the other end. Can connect straight in to AdaptaJack block. |
|
Item Code 375766 |
Headset 7A Active headset enables hands free operation for cable jointers when used with Field Telephone (Tapper) during cable change over. |
|
Item Code 377051 |
Receiver Headgear 17A Lightweight & robust headset delivers audio signals from Amp 109K & 109J to the user. Terminates on BT headset plug requiring adaptor (adaptor 315585 discontinued in 2018 replaced by Receiver Headgear 17B, see below) to connect to Tester 132K. |
|
Item Code 097057 |
Receiver Headgear 17B Lightweight & robust headset delivers audio signals from Amplifier 109K to the user. Terminated with 4 mm banana plugs to plug directly into Amplifier 109K. Used with Tester 132K. |
|
Item Code 104380 |
Test Access Clip Tee onto A & B wires through “Bed of Nails” design feature. No need to remove insulation to expose the wires, just place wires in open jaws & release. |
|
Item Code 113196 |
Tempo FED2 Mains Charger Keep Tempo FED2 Li-Ion battery in tip-top condition with Mains powered charger. |
|
Item Code 113195 |
Tempo FED2 Zipper Pouch Keep Tempo FED2 and accessories safely stored in this robust zipper pouch. |
|
Item Code 113194 |
Tempo FED2 Lanyard Lanyard to tether FED2 securely within PCP or customers premises. |
Item Code | Image | Description |
---|---|---|
Item Code 094662 |
LC-500 – Fibre Launch Box LC-500 Fibre Launch Box is a 500 metre launch cable that can be applied to each end of a fibre under test to characterise the input & output connectors. Troubleshoot the input connector & the initial fibre span that may be masked by the deadzone of the OTDR. Launch cable can also be used to minimize deadzones. |
|
Item Code 094661 |
FI-100 – LFI – Live Fibre Indicator Positively identify fibres to identify which are “Live” before disconnecting preventing loss of critical service. Direction of light travel is available for simplex circuits along with 4 tone detect frequencies: 270 Hz, 330 Hz, 1 kHz, or 2 kHz.. Precision fibre adaptors are available to match each fibre diameter introducing the correct amount of mechanical bend in the fibre without causing excessive loss, including for bend-insensitive fibre. |
|
Item Code 093689 |
180XL – VFL – Visible Light Source The 180XL Visual Fault Locator is an indispensable tool for fibre identification & continuity. Also useful for identifying bending losses and breaks in optical fibres. If a fibre is bent too tightly, red laser light will be seen escaping through the jacket. Likewise, if a fibre is broken, escaping light will be visible where the break is located. |
|
Item Code 114132 |
LC-SC Extractor Tool Secure clamp to insert or remove LC & SC type connectors from bulkheads in densely populated cabinets. |
|
Item Code 093682 |
Optitap compatible 15m test lead – SC/UPC connection Male plug used to connect test equipment to Multiport Connectorised Block Terminal (MCBT) ports located at the DP. These connectors are used extensively in FTTP & FTTH installations & can be found on OH poles & in UG chambers. |
|
Item Code 093683 |
Optitap compatible 15m test lead – SC/APC connection 9/125 Single mode, 15-metre patch cord terminating in male Optitap Compatible type plug (with Angled Physical Contact connector) at one end and SC type plug with APC connector at the other end. |
|
Item Code 093681 |
Optitap compatible 3m test lead – SC/APC connection 9/125 Single mode, 3-metre patch cord terminating in male Optitap Compatible type plug (with Angled Physical Contact connector) at one end and SC type plug with APC connector at the other end. |
|
Item Code 093684 |
Optitap compatible 3m test lead – SC/UPC connection 9/125 Single mode, 3-metre patch cord terminating in male Optitap Compatible type plug (with Angled Physical Contact connector) at one end and SC type plug with UPC connector at the other end. |
|
Item Code 093679 |
SC/APC – SC/APC Fibre Optic Test Lead – 3m 3 metre patch cord terminating in SC type plug with Angled Physical Contact connector at each end. |
|
Item Code 093680 |
SC/UPC – SC/UPC Fibre Optic Test Lead – 3m 3 metre patch cord terminating in SC type plug with Ultra Physical Contact connector at each end. |
|
Item Code 093685 |
SC/APC – SC/UPC Fibre Optic Test Lead – 3m 3 metre patch cord terminating in SC type plug with Angled Physical Contact connector at one end and Ultra Physical Contact connector at the other end. |
|
Item Code 093691 |
SC/APC – FC/UPC Fibre Optic Test Lead – 3m 3-metre patch cord terminating in SC type plug with Angled Physical Contact connector at one end and FC type plug with Ultra Physical Contact connector at the other end. |
|
Item Code 093692 |
SC/UPC – FC/UPC Fibre Optic Test Lead – 3m 3 metre patch cord terminating in SC type plug with Ultra Physical Contact connector at one end and FC type plug with Ultra Physical Contact connector at the other end. |
|
Item Code 094663 |
LC/APC – SC/APC Fibre Optic Test Lead – 3m 3 metre patch cord terminating in LC type plug with Angled Physical Contact connector at one end and SC type plug with Angled Physical Contact connector at the other end. |
|
Item Code 094664 |
LC/APC – SC/UPC Fibre Optic Test Lead – 3m 3 metre patch cord terminating in LC type plug with Angled Physical Contact connector at one end and SC type plug with Ultra Physical Contact connector at the other end. |
|
Item Code 097597 |
FC/UPC – LC/APC Fibre Optic Test Lead – 3m 3 metre patch cord terminating in LC type plug with Angled Physical Contact connector at one end and FC type plug with Ultra Physical Contact connector at the other end. |
|
Item Code 097598 |
Fibre Carrying Case Multiple pockets to carry your fibre test leads & accessories. Large pockets on the outside for longer, bulkier patch cords. |
|
Item Code 112132 |
Test Lead Carry Case Multiple pockets to carry your fibre test leads & accessories. |
|
Item Code 093686 |
SC-FC Connector/Coupler Connector adaptor to mate SC terminated fibre to FC terminated fibre. |
|
Item Code 093688 |
FC-FC Connector/Coupler Connector adaptor to mate 2 FC terminated fibre patch cords together. |
|
Item Code 093794 |
LC-LC Connector/Coupler In-line adaptor to connect 2 LC terminated fibers together. |
|
Item Code 104798 |
SC/UPC – LC/UPC Fibre Optic Test Lead – 3m 3 metre patch cord terminating in LC type plug with Ultra Physical Contact connector at one end and SC type plug with Ultra Physical Contact connector at the other end. |
|
Item Code 104799 |
LC/UPC – SC/APC Fibre Optic Test Lead – 3m 3 metre patch cord terminating in LC type plug with Ultra Physical Contact connector at one end and SC type plug with Angled Physical Contact connector at the other end. |
|
Item Code 104800 |
LC-SC Connector/Coupler Connector adaptor to mate SC terminated fibre to LC terminated fibre. |