- Sidekick Plus Standard (1155-5001 LCC / 1155-5003 SCC)
The Sidekick Plus Standard is a handheld copper test set for technicians who install, maintain and repair twisted-pair networks. It covers the core tests needed to qualify a pair and locate faults. These include AC/DC voltage, resistance, loop current, 1 GΩ insulation leakage, longitudinal balance, ground resistance and stress testing. For fault location it adds a resistive fault locator (to 20 MΩ), a dual-trace Pulse TDR with zero dead zone, an open meter (to 30 km) and load coil detection.Transmission and noise tests confirm circuit quality before a service is activated or a fault is cleared. A tracing tone (200 Hz to 20 kHz) helps identify pairs. Custom Auto Tests with pass/fail criteria give consistent results across technicians, and up to 400 results can be stored.Ideal for: Copper pair qualification, fault location and routine maintenance.
- Sidekick Plus Advanced (1155-5005 LCC)
The Advanced model includes everything in the Standard and adds Step TDR and Impulse Noise testing, for faults that basic tests don't resolve. Step TDR works alongside Pulse TDR and gives a second view of the cable, helping to locate faults such as series (high resistance), opens (disconnections) and shorts (loops). Impulse Noise testing captures short bursts of noise that can cause errors, dropouts and intermittent complaints but don't show in a single noise reading.Ideal for: Hard-to-find copper faults and noise-related service complaints.
- Sidekick Plus Wideband (1155-5009 LCC)
The Wideband model includes everything in the Advanced and adds wideband noise spectrum analysis to 35 MHz. Loss is measured to 4.4 MHz using a built-in wideband reference tone. Spectrum analysis shows the noise, interference and crosstalk that limit DSL performance, so technicians can check that a pair is fit for broadband before a service is installed.The Wideband model has no DSL modem. For DSL sync and service testing, see the Sidekick Plus DSL.Ideal for: Checking copper pairs for broadband and finding interference, without a modem.
- Sidekick Plus DSL (1155-5010 LCC / 1155-5011 SCC)
The DSL model includes everything in the Wideband and adds a built-in ADSL/VDSL modem with vectoring support. Technicians can qualify the copper pair, sync to the DSL service and confirm that it works, all with one instrument.DSL results include Showtime, SNR, bits per tone, HLOG, Quiet Line Noise and error counts. Upper-layer tests (ping, trace-route, HTTP and FTP) confirm connectivity beyond sync. Automated test scripts keep installation and repair checks consistent. Ideal for: Single-pair ADSL/VDSL installations and repairs where proof of sync and service is needed.
- Sidekick Plus Bonded DSL (1155-5012 LCC / 1155-5013 SCC)
The Bonded DSL model includes everything in the DSL and adds two-pair bonded ADSL/VDSL sync and service testing. Bonding combines two copper pairs to deliver higher speeds, or the same speed over longer distances, than a single pair can carry.Ideal for: Installing, validating and repairing two-pair bonded DSL services.
- Sidekick Plus IPTV (1155-5018 LCC)
The IPTV model is the most complete in the Sidekick Plus range. It includes everything in the Bonded DSL and adds IPTV service testing and an optical power meter. IPTV Auto Test monitors up to four channels at once. It reports channel summary, quality-of-service metrics, PID and video information, and TR 101 290 Priority 1 and 2 alarms.The optical power meter checks signal levels where fibre and copper meet, for example at a fibre-fed cabinet. With copper, DSL, IPTV and optical power testing in one handheld unit, technicians can confirm both the line and the TV service at the end of an install without switching instruments.Ideal for: DSL installations where IPTV delivery and optical power levels also need confirming.